The new home needs to be equipped with a computer and is configured as high as possible within the budget. The chassis should be small and compact in appearance. Qiao Sibo UMX1-PLUS is in the eye phase, but also got the LD's recognition. So the size of orders received, and then buy other hardware ready to install. At the same time, this is my first opportunity.
After receiving the goods, carefully measure the size and prepare to do a detailed design for the breakdown. Chassis workmanship is very good, aluminum alloy board surface has a drawing effect looks beautiful. However, compared with the ordinary chassis, some holes and the drawbacks of not being able to go back to the line still brought me a lot of trouble. The entire installation process was demolished, and the plan was modified numerous times. There is also an important reason for this is my own obsessive compulsive disorder, that is to do without any damage to the chassis to complete the installation.
After the motherboard's CPU memory power arrived, it borrowed the company's fan hard disk graphics card test machine. Originally intended to install integrated water cooling, because the top 120mm fan hole is not an external type, can only punch the screw from the outside, or use the fan in the cold in the next way (but fan and cold row connection can only be glued, There are friends on the Internet so loaded, I personally designed a non-destructive solution as shown above, only a few small parts processing is not difficult. But my mainboard CPU power socket is designed to be on the edge. When the cable is inserted, the socket just interferes with the screws in the solution.
Since the top space is not available, simply replace the original thin fan with a solar eclipse. As for water cooling, the only installation location is the 80mm fan hole on the back of the chassis. In this case, it can only be equipped with split-body water cooling. At the same time, a self-made bracket is fixed on the heat dissipation hole, the pump and the water tank are installed, and four M3 screws are fixed. In fact, the company's warehouse has a variety of metric pipe joints and water pipes, but in order to avoid being known to occupy the company's cheap, or all the net purchase. But the small thing, such as the screw nut flat washer spring washer, silently went to the unattended spare parts storage area. A 80mm thick cold row and fan and protective net were purchased online. The L-shaped bracket on the map was sent from a water tank.
Try it out and try it out. The cooling effect of water cooling is really good, and the test run is 20 degrees cooler than the air cooling. The plan has been modified once again, placing the pump in the lower right corner, installing the original thin top fan at the bottom to strengthen the air intake, and installing a restart button just in case. After the glass side covers, these things will be covered. The water tank uses the two L-shaped brackets that are presented and requires a connecting bracket in the middle. I searched for rubbish around the entire shop. I found a few similar parts, polished and drilled myself and chose the most suitable one.
In order to facilitate the release of water, an additional valve was added. The flow indicator is really not released, bought in white. If the side is not transparent, then no light is a waste. It is not possible to disguise the light pollution at the bottom of the main board and the remote control seven lights. Everything is in the office. He spends one or two hours a day after work to play a little, and engage in intermittently for a month. At last, it was a tragedy at the completion of the lighting ceremony: The LED lights had no effect on checking the insulation, which caused me to touch the chassis screws when finishing the turn of the lights. The lights were short-circuited and smoked immediately. I was excited. Just a few minutes. I bought a longer light strip and insulated it. The bottom atmosphere of the motherboard has to be removed for insulation. This means that all the hardware has to be removed. Another delay of more than a week, after the installation of a few GTA in the company, was happy to move the new machine back home. A DP-connected display, an HDMI-connected projector or TV, audio can be transmitted to the audio via fiber optics or Bluetooth, as HTPC is also OK.
Odf Box,Odf Distribution Box,White Odf Fiber Optic Patch Panel,Grid Fiber Distribution Frame
Shenzhen Jingtu Cabinet Network Equipment Co., LTD , https://www.jingtucabinet.com